2022 audi q7 rear brake pad replacement

Estimate price near me

Included for free with this service

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

How much does a Brake Pad Replacement cost?

On average, the cost for a Audi Q7 Brake Pad Replacement is $180 with $85 for parts and $95 for labor. Prices may vary depending on your location.

Show example Audi Q7 Brake Pad Replacement prices

What are brake pads and how do they work?

Brake pads consist of friction material that is bonded to a sturdy steel backing plate. When you push on the brake pedal, the friction material on the brake pads is forced against the inner and outer surfaces of the steel brake rotor under tremendous pressure. The resulting friction causes the wheels on your car to slow rapidly allowing for a quick, safe and controlled stop. After thousands of miles, this friction material eventually wears away, and the brake rotor wears away as well, requiring replacement.

When to replace brake pads?

Here are several indications that you need new brake pads:

• Wear indicator on vehicle dashboard. When the friction material on the brake pads is worn to within 2 mm of the pad backing plate, replacement of the pads is necessary. Most newer cars today have electronics built into the brake pad. When the pad is at a point that it needs to be replaced, a symbol will appear on your vehicle dashboard’s instrument cluster. Consult your owner’s manual to learn what the symbol looks like.
  
• High pitched squeal when braking. When the friction material on the pads is worn close to the backing plate, you may hear a squealing or squeaking noise as you drive regardless of whether you are applying the brakes or not. That squealing or squeaking noise is designed to make you aware that the brake pads are getting low and need to be inspected. If all of the friction material on the brake pad has been worn away, you will hear grinding and scraping noises when you apply the brakes. Pad replacement is mandatory at this point and the vehicle is unsafe to drive until corrected.
• Brake pedal pulsation or vehicle vibration. Over time, brake rotors may develop excessive thickness variation (>.001 inches), excessive runout on the wheel hub (> .002 inches), or the brake rotor may warp due to high operating temperatures. If these defects exist, you may notice pulsation in the brake pedal or steering wheel during braking. New pads and rotor resurfacing or replacement will be required if the rotor has any of the above-mentioned deficiencies.
• Vehicle pulling or wandering on braking. If your car pulls to the right or left during braking, that could be a sign of a sticking brake caliper, misalignment of the suspension, and sometimes tire defects or uneven tire inflation from side-to-side. The mechanic who inspects your vehicle will determine if new brake pads alone will resolve the issue or if other repairs are needed.
• High mileage on existing pads. Regardless of whether any of the above brake system symptoms occur, every 10,000 miles a mechanic should measure the thickness of the remaining friction material on the brake pads and perform a thorough visual inspection of the braking system.
• Brake system warning lights and/or maintenance reminder messages. Should your brake system warning light ever illuminates, or a brake system related maintenance reminder message appears in the driver information display, have your vehicle inspected and repaired as soon as possible.

How do mechanics replace brake pads?

Normally, pad replacement requires these steps:

• Confirm the thickness of the remaining friction material on the brake pads. If the remaining friction material is less than 2 mm in thickness, pad replacement is warranted.
• Visually inspect the brake rotor surface that contacts the pad (for scoring, pitting, grooves, rust) and measure the brake rotor with precision tools for thickness variation, run-out and warpage.
• Inspect the caliper, torque plate, pads, and rotors to determine if the caliper is operating freely (i.e., inspect for stuck calipers).
  
• Install new pads and any additional recommended components (e.g., rotors, if rotors depart from OEM specifications) only with customer approval of course.
  
• Lubricate brake system components, such as caliper sliding pins, and inspect the condition of the brake fluid. Top off brake fluid as required.
• Perform a basic 50 point safety inspection of your vehicle.
• Finally, the mechanic will test drive your vehicle to confirm normal operation of the brake system.

Is it safe to drive with a brake pad problem?

Driving a vehicle with a known deficiency in the braking system is unsafe and consequently is not recommended. Worn out brake pads can increase stopping distances and so for your safety, it is always advised that worn out brake pads be replaced promptly. Further driving is not recommended and you should request service at your earliest convenience if any of the following circumstances exist: stopping distances are much greater than what you are accustomed to; the brake pedal is not firm or is low; there is loss of braking power assist; the vehicle pulls severely to one side on braking; or the brake system warning light is on.

If you detect unusual noises, such as squealing or grinding, but stopping distances are close to what you are used to, and the brake pedal is firm, and there are no warning lights, it may be safe to proceed to your destination but schedule service at your earliest convenience. When it comes to the brakes on your vehicle, always err on the side of caution and have a mechanic check your brake pads and braking system at the first indication of a problem.

When replacing brake pads keep in mind:

Brake pads must always be replaced as a set, that is both wheels (driver and passenger side) on an axle, front or rear, must be serviced. If brake pads on only one side of the car were replaced, your car might pull to one side when you apply the brakes. Often, resurfacing or replacement of the brake rotors is necessary and a competent mechanic will always measure for wear and damage to the brake rotors and advise you as to whether rotor replacement or re-surfacing is needed.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Recent articles & questions

A Buyer’s Guide to the 2012 Acura TSX SportWagon

The The 2012 Acura TSX SportWagon has the perfect combination of utility and performance. The vehicle is pleasant to drive and makes luxury a priority. The TSX SportWagon uses electrically boosted power steering, which provides you with more stability driving...

Veteran and Military Driver Laws and Benefits in South Dakota

The The state of South Dakota offers several important benefits for current and veteran military service members when it comes to drivers’ licenses, license plates and more, including the fact that those stationed out of state never actually need to...

My battery went dead, replaced it with a new one and within 150 miles the Check Engine Warning Light came on.

There are a relatively large number of Technical Service Bulletins (https://www.yourmechanic.com/article/how-to-use-a-technical-service-bulletin-by-parker-hill) that GM has issued covering faults and difficulties with electrical components in your vehicle (ref: National Highway Traffic Safety Administration on-line database which we searched for your year, make...

Check engine light on

The most common causes of Diagnostic trouble code P0430 (https://www.yourmechanic.com/article/p0430-obd-ii-trouble-code-catalyst-system-efficiency-below-threshold-bank-2-by-spencer-clayton) setting are a faulty catalytic converter, engine misfire, fuel injector leakage, engine mechanical damage, faulty oxygen sensor outputs and exhaust leaks. Additionally, in your circumstance, malfunctions in the charge air...

Changed battery in kia Rio 2010, it won't start at all now. Engine light turns on at random times as well.

If you request a no/hard starting - engine diagnostic (https://www.yourmechanic.com/services/car-is-hard-to-start-inspection) the responding certified mechanic will get this resolved for you promptly. The battery should be tested to determine its state of charge. If the new battery is in fact discharged,...

1. Home
2. Estimates
3. Audi
4. Q7
5. Brake Pad Replacement

How much does it cost to replace brakes on Audi Q7?

How long do Audi Q7 brake pads last?

Why do my Audi Q7 brakes squeal?

How much does Audi charge for brake job?