COFFEEMAKER PART Show
Housing Carafe Plate Power Cord Carafe Lid Brew Basket Glass Carafes Thermal Carafes DE -S C AL I N G WIT H AUTO CLEA N Over time, calcium deposits or "scale" may build up in your brewer. Scale is nontoxic but if left unattended can hinder brewer performance. Regularly de- scaling your brewer helps to maintain quality coffee as well as the lifespan of the heating element, and other internal parts that come in contact with water throughout the brew process. To make the de-scaling process as effortless as possible, an Auto Clean system has been programmed into your coffeemaker. When is it time to Auto Clean? After every 60 brews, an icon reading 'CL' will begin to flash prior to brewing your coffee. This is to alert you that it is time to de-scale your coffeemaker. After you run the Auto Clean system, the alert will reset and blinking will stop, until it is time to clean the unit again. How do I use Auto Clean? Follow the simple steps below. Your coffeemaker will take care of the rest. 1. Fill the water reservoir approximately half-way with white vinegar. 2. Fill the remaining half of the water reservoir with cool water. 3. Place a paper basket filter into the brew basket, close the lid and place the empty carafe onto the carafe plate. 4. Press and hold both the 'AUTO' button for five seconds to start the Auto Clean system. Note: The icon reading 'CL' will remain lit to indicate that the Auto Clean system is activated. 5. Leave unit to Auto Clean for approximately 60 minutes. 6. When Auto Clean has finished, the 'CL' icon will turn off. 7. Discard the liquid in the carafe. 8. Using water only, run a minimum of two full brew cycles through your coffeemaker. 9. Wash, rinse and dry each removable piece of your coffeemaker (see the Basic Cleaning section of this guide for specific instructions). CLEANING INSTRUCTIONS Wipe with a soft, damp cloth. Wash by hand in warm soapy water, or in the dishwasher (top rack only). Wash by hand in warm soapy water 11 When your Black & Decker coffee maker stops working properly, you may be tempted to throw it away at once and buy a new one. Don’t hurry: there is every possibility that you won’t need a new coffee maker at all. Check the symptom the appliance is experiencing in the table below to find out how to solve the problem. Most likely, the coffee maker troubleshooting won’t take you more than half an hour, while some of the issues can be resolved in fifteen minutes such as coffee pot replacement. Turns on but won’t brew and not brewingThe heating element, which is located in the bottom part of the coffee maker, may remain on long coffee is completely brewed, to keep it warm. This results in quite a bit of load on the unit, causing it to break down from time to time. Not infrequently, the heating element gets shorted due to droops off water and/or coffee being spilled onto it. In some cases, the element needs to be replaced.
How to program coffee maker black and deckerIt should be noted that Black & Decker have 33 modifications. However, they are programmed in a similar fashion, so it is advisable to peep into a manual, because there can be differences. There are some common points to follow, such as:
This is the very first thing you should do once and for all. Most Black & Decker coffee makers have a delayed brewing option for more convenient brewing. Some people prefer not to use this option. It is still possible to set the timer to a specific time. To set the clock, use the HR button: press it and hold until the indication reaches the correct time. You can set the timer up to either the AM or PM mode. To set it to the PM mode, run the cycle from the 1st to 12th hour; once you do, a small PM indication will appear in the right/left side of the LCD display. Then press the HR button once again and hold it until the indication reaches the correct hour. Use the MIN button to set the minutes in the same press-hold-release fashion (the button is located right below the HR button). There is a video, which can shed some light for you on how to use the buttons set your coffee brewer’s timer.
Some people like it when a coffee maker brews at a specific time. To set it to work at a particular moment, press the PROG button and set the time as described in the previous point. The display will flash several times. This will mean that you have set your brewer up to do the job at a specific time of the day. It will jump back to the current time after a few seconds. When it does, press AUTO to activate the program.
Black & Decker GT305. GT320 coffee maker troubleshooting
Black & Decker MILL & BREW coffee maker troubleshooting
Black & Decker Spacemaker SCM1000BD coffee maker troubleshooting
Black & Decker CM1060 coffee maker troubleshooting
How do you reset the clean light on a coffee maker?A classic technology trick: unplug your coffee maker and let it sit for a minute or two. Then plug it back in. This will reset the machine, likely turning off your pesky flashing clean light.
Why does my coffee maker keep saying clean?The clean light will blink when the machine is indicating it needs to be cleaned. If the clean light is flashing while on, it is saying that there is a build-up of calcium, and it will interfere with the function of your coffee maker and flavor your coffee.
How do you clean an old Black and Decker coffee maker?Step 1: Fill the coffee maker with vinegar and water. To clean your coffee maker, begin by filling the reservoir with a 50-50 mixture of white distilled vinegar and water. ... . Step 2: Brew and let soak. Position a filter in the basket, and turn the brewer on. ... . Step 3: Finish the cycle and flush with water.. |