46 Show GETTING TO KNOW YOUR VEHICLE Rolling Code Devices To determine if your device has a rolling code, a good indicator is its manufacturing date. Typically, devices manufactured after 1995 have rolling codes. A device with a rolling code will also have a "LEARN" or "TRAIN" button located where the antenna is attached to the device. The button may not be immediately visible when looking at the device. The name and color of the button may vary slightly by manufacturer. NOTE: The "LEARN" or "TRAIN" button is not the button you normally use to operate the device. Non-rolling Code Devices Most devices manufactured before 1995 will not have a rolling code. These devices will also not have a "LEARN" or "TRAIN" button. P H L ROGRAMMING OME INK G D O ARAGE OOR PENER To program any of the HomeLink® buttons to activate your garage door opener motor, follow these steps: NOTE: All HomeLink® buttons are programmed using this procedure. You do not need to erase all channels when programming additional buttons. 1. Place the ignition switch into the ON/RUN position. 2. Place the garage door opener transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program, while keeping the HomeLink® indicator light in view. 3. Push and hold the HomeLink® button you want to program while you push and hold the garage door opener transmitter button you are trying to replicate. 4. Continue to hold both buttons and observe the HomeLink® indicator light. The ® T A HomeLink® indicator light will flash slowly O and then rapidly. Once this happens, release both buttons. NOTE: Make sure the garage door opener motor is plugged in before moving on to the rolling code/ non-rolling code final steps. Rolling Code Garage Door Opener Final Steps NOTE: You have 30 seconds in which to initiate rolling code final step 2, after completing rolling code final step 1. 1. At the garage door opener motor (in the garage), locate the "LEARN" or "TRAIN" button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor. Firmly push and release the "LEARN" or "TRAIN" button. 2. Return to the vehicle and push the programmed HomeLink® button three times (holding the button for two seconds each time). If the garage door opener motor operates, programming is complete. 3. Push the programmed HomeLink® button to confirm that the garage door opener motor operates. If the garage door opener motor does not operate, repeat the final steps for the rolling code procedure. HomeLink® Programming for Garage Door Opener5 Steps To Program Your HomeLink® System Note: Some vehicles may require the ignition be turned on or the vehicle
actually running to program the HomeLink® transceiver. If you have a newer garage door opener from Overhead Door® garage opener, including a Destiny®, Odyssey®, or Legacy® 850 and the first 5 digits of the serial numbers are 11291 or greater please find our HomeLink® Programming instructions for these newer garage door opener models. For any serial number smaller than 11291, the following programming instructions are what you will need.
Garage Door Openers that Work with HomeLink® HomeLink® is a registered trademark of Gentex Corporation. For system problems call 1-800-355-3515 or visit their website How do you program a garage door opener on a 2022 Jeep Wrangler?To learn how to program a Jeep Wrangler garage door opener, follow these steps: Find the Homelink system above your rearview mirror. Hold your door opener close to the Homelink system. Select a button on the system to use as your new door opener, and press it while simultaneously pressing down on your current door ...
How do I activate my Jeep garage door opener?While the car is ON, hold the handheld garage door transmitter 1-3 inches from the HomeLink® button you want to program in the vehicle. Push and hold both the HomeLink® button being programmed and the button on the garage door transmitter.
Does Jeep Cherokee have garage door opener?Luckily, programming a Jeep Grand Cherokee garage door opener is pretty easy—so you don't need to worry about your missing manual. All Jeeps use a HomeLink system to store data to connect to up to three different garage doors at once.
|