2014 ford f150 5.0 l oil capacity

Q: How many Litres of oil does a 2014 5.0 F150 take?

Lets start with the hard-hitting question: how much engine oil does a 2014 Ford F-150 5.0 need? Youll need 7.7 quarts (also measured as 7.3 liters) to ensure the 360-hp 5.0L V8 engine on your 2014 Ford F-150 runs smoothly.

Perform you own Ford F150 oil change and you can be sure it was done right. This guide is specifically for 2011, 2012, 2013, 2014, 2015, 2016, and 2017 F150 model years when equipped with the 5.0L Coyote V8 engine. For other Ford oil change guides, visit this page.

Table of Contents Show

Tools Needed:
Parts needed:
2011 – 2017 5.0L Ford F150 Oil Change Procedure:
How many Litres of oil does a 2014 5.0 F150 take?
What kind of oil does a 2014 F
What oil does Ford 5.0 F150 take?
How much oil does a 5l Ford F150 take?

Tools Needed:

15mm socket and ratchet or 15mm wrench
Oil filter wrench for tight oil filters
Engine oil drain pan (over 7.7 qt capacity)
Oil fill funnel
Rag to clean dipstick

Parts needed:

As an Amazon Associate I earn from qualifying purchases.

Oil FIlter – Motorcraft FL500S or equivalent filter
Engine oil – 5W20 (7.7 quart capacity)

2011 – 2017 5.0L Ford F150 Oil Change Procedure:

Park truck on a level surface
Warm engine to operating temp
Check engine oil level on dipstick to verify no issues
Loosen oil pan drain plug using the 15mm socket with the ratchet (or 15mm wrench) and let oil drain into pan
Reinstall and tighten oil drain plug once all engine oil has drained
Move drain pan under the oil filter and remove using the oil filter wrench if it is too tight to remove by hand
Clean engine oil filter mounting surface
Lubricate engine oil filter o ring using fresh engine oil
Install and tighten engine oil filter to block by hand
Clean excess spilled oil from oil pan and below oil filter – it often pools at crossmember below
Fill engine with 7 quarts of new engine oil with oil fill funnel and reinstall oil fill cap
Start engine to let engine oil pressure build to accurately check oil level
Check engine oil level & add engine oil to until oil reads to the full mark on the dip stick

Engine oil fill cap pictured on the passenger side of the engine

Oil pan drain plug

Engine oil filter pictured at the front of the engine block below the accessory belt

Ford F-150 Coyote 5.0L V8 Engine Oil Change Guide
How to change the motor oil and filter on a 12th generation 2011 to 2014 Ford F150 with the Coyote 5.0L V8 engine.

F-150 5.0L V8 Engine

Twist Off Oil Filler Cap

Yellow Handled Dipstick This automotive "how-to" guide was specifically written to assist owners of the 12th generation (2011, 2012, 2013 & 2014) Ford F-150 truck equipped with the Coyote 5.0 liter V8 engine in changing the motor oil and replacing the oil filter.

Owners of other Ford vehicles with the Coyote 5.0 liter V8 engine such as the Mustang GT, Falcon GT, and Mustang Boss 302 may also find these DIY oil change instructions to be helpful.

The items needed to complete this procedure include a 15mm socket, a ratcheting wrench, a used oil catch container, a new oil filter, 8 quarts of SAE 5W-20 oil and an automotive funnel.

A few compatible aftermarket oil filters include the following with their part numbers: Motorcraft FL500S, Mobil 1 M1-212, K&N HP-2011, Royal Purple 20-500, ACDelco PF63, Fram PH10575, Purolator PSL22500, Wix 57502, Mobil1 M1-212, Pennzoil HPZ-173, Mann Filter ML 1049 and Hastings LF641.

Pull Dipstick Up

Engine Oil Pan

Used Oil Catch Basin The first steps are to warm up the engine for a few minutes, park the truck on a level surface and shut off the engine.

Warming up the engine will help suspend any contaminants within the old oil and allow it to drain out more quickly.

Then engage the emergency parking brake and chock the front wheels to prevent the vehicle from moving.

Twist off the oil filler cap on the left side of the engine in the counter clockwise direction and lift up the yellow handled oil level dipstick on the right side of the engine. The preceding two steps will help prevent a vacuum from forming and allow the old oil to drain out more quickly.

Loosen 15mm Bolt

Draining Out Old Oil

Tighten Oil Drain Bolt Slide underneath the passenger side of the engine and locate the black metal oil drain bolt at the rear edge of the oil pan.

Place the used oil catch basin just below the oil drain bolt.

Loosen the oil drain bolt with a 15mm socket and ratcheting wrench by turning it counter clockwise.

Be careful when you remove the oil drain bolt since the old oil may be hot enough to burn your skin depending on how long you warmed up the engine in the first step. For extra safety, wear latex gloves since used motor oil is carcinogenic (cancer causing).

(This generation of the F150 is not equipped with an oil drain bolt washer or "gasket".)

Allow the old oil to drain out for a few minutes, spin in the oil drain bolt in the clockwise direction, and tighten it with the 15mm socket and ratcheting wrench to just past hand tight.

View Of Filter From Above

View of Filter From Below

Move Catch Basin Forward The canister oil filter is located at the front driver side of the engine near the serpentine accessory belt.

Move the used oil catch basin forward to just below the old oil filter.

Twist Off Old Oil Filter

Dip Pinky Finger In Oil

Lubricate Rubber O-Ring Twist off the old oil filter in the counter clockwise direction.

If you have trouble removing the filter, you may need to use an oil filter wrench such as the Lisle 63250.

Make sure that the rubber o-ring from the old filter is not stuck to the engine.

I recommend buying the Ford OEM Motorcraft FL500Soil filter since it has excellent reviews on Amazon.

Dip your pinky finger in to some new oil and lubricate the rubber o-ring on the new oil filter. Lubricating the oil filter o-ring will help it form a better seal and make it easier to remove at the next oil change.

Spin On New Filter

Insert Automotive Funnel

Pour In New SAE 5W-20 Spin on the new oil filter in the clockwise direction to about 1/4 to 1/3 turn past hand tight. Do not over tighten the oil filter or use an oil filter wrench to tighten it.

Insert the automotive funnel in to the oil filler hole and pour in about 7 quarts of the engine's 8 quart total capacity for an oil change with filter replacement.

(It is far better to have slightly less oil in an engine than too much.)

Replace Oil Filler Cap

Pull Out Oil Level Dipstick

Check Level On Dipstick Temporarily replace the oil filler cap and push in the oil level dipstick.

Turn on the engine for a few minutes, shut it off, and allow it to rest for at least 5 to 10 minutes so that the oil drains back to the pan.

Check the oil level on the dipstick and slowly continue adding more oil until the level reaches just at or below the upper hole in the metal.

You may not need to use the entire 8 quarts of new SAE 5W-20 oil depending on how long you allowed the old oil to drain out.

For more, check out my other Ford F-150 Repair & Maintenance Guides.

How many Litres of oil does a 2014 5.0 F150 take?

Let's start with the hard-hitting question: how much engine oil does a 2014 Ford F-150 5.0 need? You'll need 7.7 quarts (also measured as 7.3 liters) to ensure the 360-hp 5.0L V8 engine on your 2014 Ford F-150 runs smoothly.

What kind of oil does a 2014 F

Mobil 1 - Extended Performance High Mileage 5W-20 Full Synthetic Motor Oil, 5 Quart (Part No. 15020) Product Features: Mobil 1 Extended Performance High Mileage full-synthetic motor oil 5W-20 is designed for engines with over 75,000 miles to go up to 20,000 miles between oil changes.